International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Tire Kickin' > Build Threads

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-06-2022, 08:00 PM
Warlordsix Warlordsix is offline
230 Tornado
 
Join Date: Dec 23, 2021
Location: SE USA
Posts: 21
Warpig - Shortbed Pickup - Bobbed YJ Wrangler Body on GW Chassis

Okay, kids, here's the plan...I'm building what Jeep doesn't build, a V8-powered, 5-speed, 4x4 shortbed, 2-door pickup. For years I've been thinking about how I would do this. I've finally pulled the trigger. I'm in the middle of the project now.

1. Started with an '88 GW. Previous owner installed a 3" lift. I pulled the body off and exposed a totally solid, rust-free frame w Dana 44s.

2. Procured a '92 YJ, 4.0L, 5-speed (AX-15) for the donor. I will use the body & interior, flywheel, (will need to be match balanced to the flexplate of the AMC360), tranny and transfercase (NP231), shifters, hydraulic clutch, fuel tank, steering column, basically everything but the frame, axles, suspension, wheels, etc.

3. I procured a bellhousing, clutch master & slave & line & input bearing support from a '94 4.0 YJ, because I want to run an external clutch slave cylinder (which became available in'94). If I wanted to keep the '92 YJ's internal hydraulic throwout bearing, I wouldn't have had to buy any of that stuff. Could have just swapped everything over from the YJ. BTW, this AX15 swap is possible with ALL Jeep parts! Only part I needed to buy separately was a pilot bearing to match the larger bore in the AMC 360 crank to the pilot tip of the AX15. The PN for that pilot bearing is National Bearing FC69907

4. I will need to move the AMC 360 motor mounts rearward aprox 9" (final distance will soon be determined after I drop the YJ body onto the frame to start mocking things in). The determining issue will be locating the front axle in the center of the YJ front fender opening.

5. I will bob the YJ tub by chopping a section (length TBD) out of the rear seat area and welding the rear corners/taillight area back onto the shortened tub. I will then build a custom bed (similar to a Jeep TJ Brute bed) to be mounted behind the tub.

6. I will bob the hardtop to match the bobbed tub. Objective is to leave ample room behind the driver/passenger seat for a good-sized tool box, lockable storage, etc.

7. I will have to fab new or shortened/lengthened driveshafts, as the tranny/transfercase will be located 9" or so rearward along with the engine.

8. I installed brand new locking hubs into the front Dana 44 axle. The stock axle ratios, however, stink. 2.73. Eventually, I will have those swapped for something lower, but I'm not spending any time on that now.

9. AMC 360 will eventually be rebuilt or swapped for a fresh rebuild. Mods will be moderate. For ignition I'm installing a TFI upgrade, but I'm gutting the stock Duraspark box and installing an HEI module inside it. Intake is an Edelbrock Performer and carb is a Holley Street Avenger 670 with vacuum secondaries. I'm running the stock, AMC high-flow passenger side exhaust manifold and swapping on a matching, high-flow driver side exhaust manifold.

10. If you're curious how this might turn out, do a search for Sitting Bull's Crackpipe. I discovered that project after I began my project, and it is very close to what I'm doing. The big differences are he kept his TF727 and stretched his YJ body to make it more like a Scrambler. I'm running a 5-speed and a separate bed (which will likely be almost a 5' bed).

I'll post plenty of photos and welcome suggestions, tips, etc. For now the project is well underway, so I should have the first photos up fairly soon.

Ernie

Last edited by Warlordsix : 06-06-2022 at 08:20 PM.
Reply With Quote
  #2  
Old 06-06-2022, 10:50 PM
cu4whln's Avatar
cu4whln cu4whln is offline
304 AMC
 
Join Date: May 16, 2008
Location: Canton, Mi USA !
Posts: 1,621
Interesting project..

Looking forward to some pics to understand this build!

Go Man Go !
__________________
It's not yours 'til ya bleed on it . . .

1977 "401" 'Da Chief
1979 Chero: "Madness" [Sold]
1985 CJ : Renegade -locked and loaded
2005 Unlimited Rubicon - Built
2001 XJ : Driver - 2016 JK 2 door

'Da Chief here: http://www.ifsja.org/forums/vb/showt...ighlight=chief

Round 2- LT Swap: 'Da Chief:
http://www.ifsja.org/forums/vb/showthread.php?t=188457

"Madness" build here:
http://www.ifsja.org/forums/vb/showthread.php?t=89280
Reply With Quote
  #3  
Old 06-07-2022, 06:12 AM
Warlordsix Warlordsix is offline
230 Tornado
 
Join Date: Dec 23, 2021
Location: SE USA
Posts: 21
Thanks, CU. Here's a link to my corresponding post on another forum (it's WAY easier to post photos to that forum than it is to this forum. I probably will just keep posting photos to that forum, so watch there for updates. Here's the link: https://www.fsjnetwork.com/forum/vie...212998#p212998

Ernie
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
2010 PA Jeep Show Hammered Events 183 02-09-2011 07:08 AM
62 pickup needs a new chassis bherde General FSJ Tech 1 03-16-2010 08:01 AM
cj5 body on a waggy chassis? panama red General FSJ Tech 13 07-30-2007 12:59 PM
wrangler body "lift-mounts" on an fsj? Human Remains Off-Road FSJ Tech 8 04-30-2007 05:27 PM
Wagoneer Body Swap (73 body -> 74 chassis) tomd General FSJ Tech 3 10-01-2002 02:06 PM


All times are GMT -6. The time now is 12:14 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
corner corner