need a SIMPLE answer for a TFI question

[bowtieman55]

ugg...where is Jode when I need him

I went to NAPA this morning, to pick up the ICC1 coil-plug wire and the ICR22 resistor unit that buildyour4x4.com specified.
"Your stock ignition module could very likely fail if you use the full 12 volts, so we recommend using only 8 volts. If you want to run it with the lower voltage like Ford did, then you would simply put a resistor wire (see the part numbers chart above) in between the coil and the (+) power source."
The resistor wire is over 4 foot long and has a male terminal on each end. Now I have no idea how to wire it in...or if I even need it. I don't want to take a chance on burning up my stock ignition module.
I'M DEFINITELY ABOUT TO PULL THE REST OF MY HAIR OUT.

[GWChris]

so the general concensus is that it is OK to use the factory 2 coil wires...along with the resistor that I will be putting in there

This is why I posted the cmment I did - I didn't think it was clear.

The factory coil wire IS a resistor - you should not need an additional resistor. If you want to drop the voltge from the full 12V, then just hook it up with the factory wire, no need to add anything else.

[bowtieman55]

so the general concensus is that it is OK to use the factory 2 coil wires...along with the resistor that I will be putting in there

[Rande]

I used the factory coil wire on my TFI and it works just fine.

Sure, the coil can handle 12v but over the years here, I've read plenty about the ignition module frying with 12v. As I said, I used the factory wiring and now 4 years later, its still working great.

[Lindel]

That's why I said using 12V will give a little boost, but is not necessary.

[GWChris]

Looking at the wiring diagrams, the wire that feeds the coil on the horseshoe connector is a resistor wire. It would appear that if you use the factory wire, the voltage to the coil will not be 12V.

[Lindel]

You can use the wires from the horseshoe connector with no problem, in fact it's the easiest way to hook up the new coil.

Using 12V will give you a little boost in the spark, but it's not necessary.

[jeepfan93]

I have run both and no problem. No power differnece either way that i can feel. Another option is to lose the factory IM and replace it with a GM HEI. Did this on my 91 and will do it to my other trucks. 18 bucks for the module and about twenty minutes to install.

[bowtieman55]

I've searched here, there, and everywhere. I can't seem to find an answer to what I'm asking. I'm doing the TFI upgrade on my '90 this coming weekend. I plan to use the Echlin ICR22 resistor when I install my coil, because at buildyour4x4.com, they recommend it (so I don't burn up my stock module with 12 volts). That's all well and good (even though the Tech install on the IFSJA homepage says not to use one).
MY QUESTION IS...
Why can't I just use the 2 wires that the original canister coil is using to hookup my new TFI coil?
According to buildyour4x4, I'm supposed to find a keyed power wire, etc.
Hook up the TFI coil

"You?ll need to find a power source that has 8-12 Volts when the vehicle is running and zero when the ignition is off. This will be the power source for the coil. In Ford?s original TFI setup, only 8 Volts are provided to the coil. However, there is some general consensus that the coil can safely handle a full (12 V) power supply. Your stock ignition module could very likely fail if you use the full 12 volts, so we recommend using only 8 volts. If you want to run it with the lower voltage like Ford did, then you would simply put a resistor wire (see the part numbers chart above) in between the coil and the (+) power source. We chose to run the full 12 Volts directly to the coil for maximum power output. This resulted in our stock (OEM) coil becoming uncomfortably hot, and we ended up swapping out our ignition module with a prototype for the Mutant ignition module that can run on the full 12 volts. We recommend either upgrading your ignition module, or using the resistor wire to reduce the voltage. You?ll want to study the wiring diagrams posted below until you are comfortable that you have found the correct wires to splice into before you hook up your system. Once you have found the switched power source, splice it into the red wire on the TFI coil plug connector. Splice one of the green wires on the TFI coil plug connector to the green wire that comes out of the ignition module. The other green wire is not required, and can be cut off, or it can be left for future use in wiring up a tachometer."

PLEASE keep the answer fairly simple, as I don't do so well comprehending what I can't "see". TIA