International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Tire Kickin' > General FSJ Tech

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 03-29-2012, 10:13 PM
caionneach's Avatar
caionneach caionneach is offline
350 Buick
 
Join Date: Aug 19, 2003
Location: Monroe, Louisiana
Posts: 1,022
U-joint yoke & driveshaft question

I have the possibility looming before me of the necessity to switch out transmissions and transfer cases if my stock transmission has internal problems.

My rig is a 82 Cherokee with 258 six cylinder engine, T5 manual 5 speed, NP208 transfer case.

If my transmission is bad, & I'm pulling it tomorrow and will then know, I may opt to install the NP435 & NP205 I have. My question is about the yokes & u-joints from the transfer case to the axles, as the yoke on the NP205 appears to be a good bit beefier than the stock yokes on the Jeep axles.

I am under the impression that the Jeep yokes/u-joints are known as 1310, and those on the NP205 may be 1350. So please chime in if you know what these are.
__________________
1982 Cherokee
258 cid/T-5 $15 Sunpro Voltmeter gauge
replacement; Quadratec Trailmax Thermal Pro
Seats! 4 inch SKYJACKER suspension lift, 33X12.5 in
BFG Mud Terrain Tires on 15X10 in ProComp Rims.
New BJ's chrome-moly rear axle shafts, 3.73:1 diffs and ARB Air Locker!
Reply With Quote
  #2  
Old 03-30-2012, 04:54 AM
Tad's Avatar
Tad Tad is offline
 
Join Date: Nov 30, 2001
Location: Out West
Posts: 17,617
Not sure what they might be without measuring them.
http://www.pirate4x4.com/tech/billavista/PR-shaft/
About 2/3 of the way down the page are the dimensions of the more common joints.

Lots of options out there and there are conversion joints that allow you to run say a 1310 on one side and a 1350 on the other.
I was able to get the 1410 yoke from a Dodge 205 to work on my Dodge 208 simply by finding the proper seal.
__________________
2000 Infinity QX4, 3.3L, MPFI, 4 speed auto, 2 speed Nissan tcase, Unibody, IFS front, 4 link rear solid axle with 255-70/16s

IFSJA WMS PROJECT
EARLY WAG LIFT SEARCH

Quote:
...Pay no attention to these heathen barbarians with their cutting torches and 8" lift kits!...

Self Inflicted Flesh Wound
Reply With Quote
  #3  
Old 03-03-2021, 01:57 PM
caionneach's Avatar
caionneach caionneach is offline
350 Buick
 
Join Date: Aug 19, 2003
Location: Monroe, Louisiana
Posts: 1,022
U joints

There should be no need to change out the yoke assembly in the transfer case housing.

The U-joints, however, can be adapted. The SJ Jeeps have a 1310; the u-joint on the NP435/205 combo I have, allegedly from an 80s era Bronco, is more substantial. Perhaps it's a 1350.
__________________
1982 Cherokee
258 cid/T-5 $15 Sunpro Voltmeter gauge
replacement; Quadratec Trailmax Thermal Pro
Seats! 4 inch SKYJACKER suspension lift, 33X12.5 in
BFG Mud Terrain Tires on 15X10 in ProComp Rims.
New BJ's chrome-moly rear axle shafts, 3.73:1 diffs and ARB Air Locker!
Reply With Quote
  #4  
Old 03-03-2021, 02:14 PM
J20 project's Avatar
J20 project J20 project is offline
304 AMC
 
Join Date: Dec 27, 2000
Location: Nevada
Posts: 2,482
hmmm, a post from 2012 mixed w/ now...


What help is needed here..? crossover ujoint, new yoke...I can do both.

J20 project.
__________________
BP Drivetrain...........

Driveshafts for all Jeeps, Constant velocity rebuilds, Replacement, Repair
775-537-7918

https://www.facebook.com/BPShafts/

Putting this back up. "Someone is gonna have to crawl under the rig"
Reply With Quote
  #5  
Old 03-03-2021, 02:21 PM
J20 project's Avatar
J20 project J20 project is offline
304 AMC
 
Join Date: Dec 27, 2000
Location: Nevada
Posts: 2,482
caionneach

So, did you still need help here?


J20
__________________
BP Drivetrain...........

Driveshafts for all Jeeps, Constant velocity rebuilds, Replacement, Repair
775-537-7918

https://www.facebook.com/BPShafts/

Putting this back up. "Someone is gonna have to crawl under the rig"
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Owner Friendly Driveshaft? mngatewood General FSJ Tech 11 08-19-2009 08:49 AM
A question about lifts and Driveshaft Angles bashbro1 Off-Road FSJ Tech 7 11-24-2008 11:30 AM
Yoke question CRASH076 General FSJ Tech 0 10-02-2008 05:39 AM
SOA front driveshaft question fullsizejohn Off-Road FSJ Tech 10 09-02-2007 05:37 PM
SOA - Driveshaft Question Snakeyes_Tx General FSJ Tech 7 04-27-2001 07:37 PM


All times are GMT -6. The time now is 02:10 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
corner corner