International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 25 of 500
Search took 0.39 seconds.
Search: Posts Made By: porchpiggy
Forum: General FSJ Tech 08-09-2003, 05:16 PM
Replies: 1
Views: 731
Posted By porchpiggy
Post Is that the Thrush one?? I run a Thrush turbo....

Is that the Thrush one?? I run a Thrush turbo. about 17 bucks, nice low rumble but not loud at all.
Forum: General FSJ Tech 08-08-2003, 09:19 PM
Replies: 7
Views: 867
Posted By porchpiggy
Post That is impressive, but I wonder what RPM it's...

That is impressive, but I wonder what RPM it's turning to get that number, and what is the low end tourque like.
Forum: General FSJ Tech 08-07-2003, 07:58 PM
Replies: 1
Views: 462
Posted By porchpiggy
Post Easiest way is to put your finger over the #1...

Easiest way is to put your finger over the #1 spark plug hole while turning the engine, you can easily feel the puff of air as it is in the compression stroke, then line up the timing mark. Should be...
Forum: General FSJ Tech 07-10-2003, 05:06 PM
Replies: 4
Views: 584
Posted By porchpiggy
Post Don't forget the cable bracket spacer .

Don't forget the cable bracket spacer .
Forum: General FSJ Tech 06-29-2003, 01:59 PM
Replies: 7
Views: 496
Posted By porchpiggy
Post I'm guessing carbon build up on the piston also....

I'm guessing carbon build up on the piston also. Another good way to "clean" it out is with Sea Foam. followthe directions on the can, basically you pour it down the carb with the engine running....
Forum: General FSJ Tech 06-27-2003, 10:38 PM
Replies: 21
Views: 1,317
Posted By porchpiggy
Post Here it is. I bent it back down a little...

Here it is. I bent it back down a little already.

http://www.angelfire.com/ex/tongy605/ValCov
Forum: General FSJ Tech 06-27-2003, 07:52 PM
Replies: 21
Views: 1,317
Posted By porchpiggy
Post It pulled through the bolts on the intake...

It pulled through the bolts on the intake manifold side, bent and ripped the holes bigger, then folded back about half way. I'll get a pic up. I found some chrome valve covers for 18 bucks plus 10...
Forum: General FSJ Tech 06-26-2003, 10:27 PM
Replies: 21
Views: 1,317
Posted By porchpiggy
Post I had sprayed the fluid in the carb and tried to...

I had sprayed the fluid in the carb and tried to start it, but it did not start due to the bad ignition module. By the time I aquired a new module and installed it the truck sat about 20 hours.
Forum: General FSJ Tech 06-26-2003, 08:59 PM
Replies: 21
Views: 1,317
Posted By porchpiggy
Post I had a problem with my 88 GW all of a sudden not...

I had a problem with my 88 GW all of a sudden not starting. Went through all the troubleshooting, and thanks to a good education from reading this board, figured out it was a bad ignition module. I...
Forum: General FSJ Tech 06-04-2003, 06:08 PM
Replies: 5
Views: 495
Posted By porchpiggy
Post When my CV jont on the front driveshaft went bad...

When my CV jont on the front driveshaft went bad it made a ticking noise, and I would have sworn it was coming from the transfer case. Crawl under and grab the front shaft and push up and down and...
Forum: General FSJ Tech 06-04-2003, 06:04 PM
Replies: 15
Views: 428
Posted By porchpiggy
Post My CV joint made a tick-tick noise as well, like...

My CV joint made a tick-tick noise as well, like they do on front wheel drive cars when they are about to go. I could hear it really well when I drove in a tunnel or next to buildings, I did not know...
Forum: General FSJ Tech 06-03-2003, 05:47 PM
Replies: 15
Views: 428
Posted By porchpiggy
Post What's the noise like?? Is it a grinding or a...

What's the noise like?? Is it a grinding or a humm?? Does it have a tick-tick-tick to it? Some possibilities are front bearings, the front spindle bearings, or the CV joint onthe front drive shaft.
Forum: General FSJ Tech 05-28-2003, 11:04 AM
Replies: 23
Views: 1,092
Posted By porchpiggy
Post I've seen one way bleeder screws that you replace...

I've seen one way bleeder screws that you replace your bleeder screws with, when you open them they have a check valve that only allows the fluid to go out, no air in. These are available at parts...
Forum: General FSJ Tech 05-22-2003, 02:02 PM
Replies: 5
Views: 586
Posted By porchpiggy
Post The tires are 10.50 x 31's, the AT version of the...

The tires are 10.50 x 31's, the AT version of the mud kings you see so many of. They are from PO, I'm looking at some procomp muds. Actually the blue car is a 95 crown vic police interceptor, my...
Forum: General FSJ Tech 05-22-2003, 01:36 PM
Replies: 5
Views: 586
Posted By porchpiggy
Post Sluggo: http://www.angelfire.com/ex/tongy605/Slugg...

Sluggo:
http://www.angelfire.com/ex/tongy605/Sluggo
Soon to be down hard for a mopar 413, lift, and cammo paint. She's an old New Mexico truck with no rust, only 109k miles, but a bad bad case of...
Forum: General FSJ Tech 05-19-2003, 12:29 AM
Replies: 4
Views: 562
Posted By porchpiggy
Post Found...

Found it!!

http://www.ifsja.org/cgi-bin/ubbcgi/ultimatebb.cgi?ubb=get_topic;f=2;t=016200
Forum: General FSJ Tech 05-18-2003, 08:07 PM
Replies: 4
Views: 562
Posted By porchpiggy
Post Zorm, the easiest way to do it would be to use a...

Zorm, the easiest way to do it would be to use a ford tranny and transfer case, and see where you end up with drive shafts. Some one on here has swapped in a 351 and said it was very easy, but he has...
Forum: General FSJ Tech 05-17-2003, 11:54 AM
Replies: 5
Views: 515
Posted By porchpiggy
Post Your coil normally gets less than 12 volts...

Your coil normally gets less than 12 volts through a resistance wire, however when in the "start" mode it gets a full 12 volts. If your switch wqas sticking at all in the start mode then this would...
Forum: General FSJ Tech 05-16-2003, 10:17 AM
Replies: 10
Views: 554
Posted By porchpiggy
Post Yes, or there abouts. The shocks you see listed...

Yes, or there abouts. The shocks you see listed as 2-4" lifted are referring to the shock has been measured (and extends longer) to work on a vehicle that has been lifted. The best way to do it is to...
Forum: General FSJ Tech 05-08-2003, 11:25 AM
Replies: 7
Views: 624
Posted By porchpiggy
Post I have a holley 500 cfm I put on a stock 302 ford...

I have a holley 500 cfm I put on a stock 302 ford truck, ran great pretty much out of the box. I really like the carb, it's pretty easy to work on, but I don't off road this truck. Do you have to...
Forum: General FSJ Tech 05-06-2003, 11:51 AM
Replies: 4
Views: 812
Posted By porchpiggy
Post Parts Store computer says Dexron, six pints. It...

Parts Store computer says Dexron, six pints. It actually says dexron II, but I know Dexron III is the correct replacement.
Forum: General FSJ Tech 05-04-2003, 07:54 PM
Replies: 5
Views: 429
Posted By porchpiggy
Post I've seen posts on here where the opening in the...

I've seen posts on here where the opening in the intake for the PCV itself was cloged, or the "vents" in the shield on the underneath side of the PCV opening in the intake manifold.
Forum: General FSJ Tech 05-03-2003, 09:26 AM
Replies: 6
Views: 884
Posted By porchpiggy
Post Not sure of the size, but most parts stores...

Not sure of the size, but most parts stores should carry them, it's not that uncoomon for someone to need some.
Forum: General FSJ Tech 05-01-2003, 04:20 PM
Replies: 6
Views: 313
Posted By porchpiggy
Post Maybe it's a belt slipping? See if your fan belt,...

Maybe it's a belt slipping? See if your fan belt, PS belt feel tight.
Forum: General FSJ Tech 04-24-2003, 02:14 PM
Replies: 8
Views: 646
Posted By porchpiggy
Post If you have seprate turn and brake lights on your...

If you have seprate turn and brake lights on your chero, (I think 83 does) you are also going to need the module that converts to the "one light each side" (on the trailer) for brake and turn lights.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 06:42 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner