International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 11 of 11
Search took 0.00 seconds.
Search: Posts Made By: GRUNT
Forum: General FSJ Tech 03-02-2004, 11:56 PM
Replies: 2
Views: 569
Posted By GRUNT
Post I have a 75 J-20 4" lift/360 4...

I have a 75 J-20 4" lift/360 4 barrel/edelbrock setup. The engine is a year old. T-18 trans. My problem is I keep burning up transfer cases. They still work but the transfer case makes a gringing...
Forum: General FSJ Tech 03-02-2004, 11:55 PM
Replies: 2
Views: 488
Posted By GRUNT
Post I have a 75 J-20 4" lift/360 4...

I have a 75 J-20 4" lift/360 4 barrel/edelbrock setup. The engine is a year old. T-18 trans. My problem is I keep burning up transfer cases. They still work but the transfer case makes a gringing...
Forum: General FSJ Tech 02-01-2004, 02:49 PM
Replies: 1
Views: 528
Posted By GRUNT
Post I have a 75 J-20 T18/D20 setup. If I drive on the...

I have a 75 J-20 T18/D20 setup. If I drive on the pavement with snow on the pavement in 4hi at about 40 mph or in 2 hi with the hubs locked my hubs disengage and make a horrible vibration and noise....
Forum: General FSJ Tech 02-01-2004, 09:24 AM
Replies: 6
Views: 958
Posted By GRUNT
Post right on I just wanted to ask because I have a...

right on I just wanted to ask because I have a holley 600 on my j-20 but it keeps killing power valves and I'm tired of it and don't have time to mess with it. I just don't want the j-20 to be...
Forum: General FSJ Tech 02-01-2004, 08:47 AM
Replies: 6
Views: 958
Posted By GRUNT
Post If not can I put bigger fuel rods in it or...

If not can I put bigger fuel rods in it or something?
Forum: General FSJ Tech 02-01-2004, 08:46 AM
Replies: 6
Views: 958
Posted By GRUNT
Post I was given a new in box edelbrock 500 cfm carb....

I was given a new in box edelbrock 500 cfm carb. I have the edelbrock 4 barrel intake already installed. will a stock 360 be fed enough gas with a 500 cfm?
Forum: General FSJ Tech 12-07-2003, 12:37 AM
Replies: 14
Views: 3,245
Posted By GRUNT
Post Can you put higher compression pistons in a 401...

Can you put higher compression pistons in a 401 ranger?
Forum: General FSJ Tech 04-26-2003, 06:29 AM
Replies: 6
Views: 494
Posted By GRUNT
Post I have a 75 J-20 rebuilt 360 4 speed dana...

I have a 75 J-20 rebuilt 360 4 speed dana 20/60/44
. I have balanced all the wheels. no damage to the drive shaft(dents exc,) I checked the u joints. They are not loose nor do thay make any noise and...
Forum: General FSJ Tech 02-04-2003, 05:42 AM
Replies: 8
Views: 852
Posted By GRUNT
Post Thanks a lot. I was used to the old closed...

Thanks a lot. I was used to the old closed knuckle frontends on my previous Kaiser FSJs. I checked my wheel bearings they are good. I don't plan on doing nothing radical with mine. I think it's fine...
Forum: General FSJ Tech 02-04-2003, 03:36 AM
Replies: 8
Views: 852
Posted By GRUNT
Post Thanks I would have never guessed it just floated...

Thanks I would have never guessed it just floated like that. The u joint is fine. Thanks. Dimitri
Forum: General FSJ Tech 02-03-2003, 10:34 PM
Replies: 8
Views: 852
Posted By GRUNT
Arrow I bought a 75 J-20. The front end is a dana 44...

I bought a 75 J-20. The front end is a dana 44 open knuckle. When I examined mu U joints at the knuckle, I noticed I can move the left up and down in the axle housing about 1/4 of an inch. Obviously...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -6. The time now is 01:55 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner