International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 25 of 184
Search took 0.04 seconds.
Search: Posts Made By: 1BDWAGN
Forum: General FSJ Tech 09-26-2006, 05:13 AM
Replies: 44
Views: 1,778
Posted By 1BDWAGN
No oil pressure

You could always plumb in a mechanical gauge, pull the dist, and use a priming tool to check for oil pressure instead of starting the engine and relying on the factory gauge.
Forum: General FSJ Tech 09-26-2006, 05:05 AM
Replies: 5
Views: 1,589
Posted By 1BDWAGN
Results of CTO test

OK, when I got home last night I broke out the vacuum gauge and checked all CTO and linear valve connections. At idle (approx. 900 rpm in park). I got a steady 17" from the bottom of the HDC spark...
Forum: General FSJ Tech 09-25-2006, 10:38 AM
Replies: 5
Views: 1,589
Posted By 1BDWAGN
EGR

I made sure that the EGR was only receiving a ported vacuum signal when warm and that is the case. It was not stuck (I checked) and has about 10K miles on it. The intake tract is fairly clean because...
Forum: General FSJ Tech 09-25-2006, 06:53 AM
Replies: 5
Views: 1,589
Posted By 1BDWAGN
Rough idle while cold

I had a problem creep up about 2 months ago. The sympton is a really rough idle during a cold start and while the Wagon is warming up. Also the exhaust smells really rich. Adjustments to the choke...
Forum: General FSJ Tech 06-13-2005, 01:50 AM
Replies: 14
Views: 974
Posted By 1BDWAGN
Post I also used a die grinder and a flap wheel to...

I also used a die grinder and a flap wheel to smooth the inside of the manifolds up and take out any casting flash. In my opinion these manifolds don't really look like a huge restriction.
Forum: General FSJ Tech 06-10-2005, 05:18 AM
Replies: 11
Views: 529
Posted By 1BDWAGN
Post Replaced the vacuum hoses lately? Mine had a...

Replaced the vacuum hoses lately? Mine had a shaky idle ever since I bought until about 3 months ago. The intake gasket was bad. Now it is real smooth and runs great.
Forum: General FSJ Tech 06-09-2005, 01:28 AM
Replies: 4
Views: 661
Posted By 1BDWAGN
Post Check the hose to the power valve for sign of...

Check the hose to the power valve for sign of gas. Doesn't take much to pull the top of the carb off and check things out.
Forum: General FSJ Tech 06-01-2005, 04:56 AM
Replies: 7
Views: 562
Posted By 1BDWAGN
Post That's about the best pic I have so far. ...

That's about the best pic I have so far.
http://www.fullsizejeeps.com/jeeps/files/AZ_FSJers/jeep9.jpg
Here's another
http://www.fullsizejeeps.com/jeeps/files/AZ_FSJers/jeep10.jpg

I have had...
Forum: General FSJ Tech 06-01-2005, 04:06 AM
Replies: 7
Views: 562
Posted By 1BDWAGN
Post I have that combo and it's not terrible. I drive...

I have that combo and it's not terrible. I drive on the freeway a lot so it works well. Even climbing the mountains going up north I've still got passing power. The low end torque of the 360 really...
Forum: General FSJ Tech 05-25-2005, 02:07 AM
Replies: 9
Views: 601
Posted By 1BDWAGN
Post Umm I bought a new exhaust manifold and it came...

Umm I bought a new exhaust manifold and it came with some funky solid bolts so they must be available. Just use and easy out to get the ones that break out. Plan to pull the manifolds after you break...
Forum: General FSJ Tech 05-23-2005, 04:12 AM
Replies: 7
Views: 644
Posted By 1BDWAGN
Post The module is grounded through the attaching...

The module is grounded through the attaching bolts. Also I added an extra ground to one of the bolts that goes to a self-tapping screw I installed in the firewall (Sanded the paint on the firewall)....
Forum: General FSJ Tech 05-23-2005, 02:49 AM
Replies: 7
Views: 644
Posted By 1BDWAGN
Post So I can just tape it into the wire loom and...

So I can just tape it into the wire loom and forget about it. Thanks.
Forum: General FSJ Tech 05-23-2005, 01:26 AM
Replies: 7
Views: 644
Posted By 1BDWAGN
Post Well I must say that after doing the TFI...

Well I must say that after doing the TFI conversion, replacing the intake gaskets, and now swapping an HEI module for the stock one my '88 Wagon is running awesome. I made a little shelf for the...
Forum: General FSJ Tech 05-09-2005, 09:30 AM
Replies: 7
Views: 532
Posted By 1BDWAGN
Post This part has no tabs. It was originally on...

This part has no tabs. It was originally on RockCandy's Golden Eagle.
Forum: General FSJ Tech 05-09-2005, 01:44 AM
Replies: 7
Views: 532
Posted By 1BDWAGN
Post I have a factory push bar/grille guard from a '79...

I have a factory push bar/grille guard from a '79 Cherokee. I want to mount it on my Wagon and have some questions before I do so. First, do the stock bumper guards interfere? Second will the stock...
Forum: General FSJ Tech 04-23-2005, 03:37 AM
Replies: 10
Views: 981
Posted By 1BDWAGN
Post You are probably talking about the smog pump.

You are probably talking about the smog pump.
Forum: General FSJ Tech 04-14-2005, 01:26 AM
Replies: 7
Views: 713
Posted By 1BDWAGN
Post Ummm, I have 32" M/Ts with a Bj's 4"...

Ummm, I have 32" M/Ts with a Bj's 4" lift. I get a slight amount of rubbing at some points and I don't do anything hardcore. To me I think you would need to trim more then 3-4". I'd just stick with...
Forum: General FSJ Tech 04-06-2005, 09:23 AM
Replies: 0
Views: 512
Posted By 1BDWAGN
Post Does anyone know what the exact float level of an...

Does anyone know what the exact float level of an 88 GW should be? I still haven't got my Wagon through emissions. I have a vacuum leak at the base of the carb or in that area. Seems most prominent...
Forum: General FSJ Tech 03-18-2005, 07:44 AM
Replies: 7
Views: 422
Posted By 1BDWAGN
Post That is strange because I thought the factory...

That is strange because I thought the factory wired the horn so it only worked when the key was in the run, start or acc. position. Most likely a short on a wire somewhere or a bent contact under the...
Forum: General FSJ Tech 03-18-2005, 06:58 AM
Replies: 1
Views: 949
Posted By 1BDWAGN
Post Check that the top port holds vacuum. Mine does...

Check that the top port holds vacuum. Mine does not so the diaphragm must have a hole or something causing a vacuum leak. I checked mine with the engine up to temp and the valve on the side had no...
Forum: General FSJ Tech 03-18-2005, 12:47 AM
Replies: 21
Views: 1,260
Posted By 1BDWAGN
Post I have spent more then enough to apply for the...

I have spent more then enough to apply for the waiver ($450 for 81 and up). However, I would like to get everything working as it should. It may mean I won't be driving the Jeep for a little bit...
Forum: General FSJ Tech 03-17-2005, 02:19 PM
Replies: 21
Views: 1,260
Posted By 1BDWAGN
Post Well I checked the diverter valve and it appears...

Well I checked the diverter valve and it appears to be bad. The part on the top does not hold a vacuum. The check valve on the tube to the cat was crumbling from inside out. The check valve on the...
Forum: General FSJ Tech 03-17-2005, 08:07 AM
Replies: 21
Views: 1,260
Posted By 1BDWAGN
Post Does anyone know what the float setting is on...

Does anyone know what the float setting is on carb 1RHM2? I'm going to check over the carb and test the air system next.

Just found it in the tech page. 9/16"

[ March 17, 2005, 02:16 PM: Message...
Forum: General FSJ Tech 03-16-2005, 07:10 AM
Replies: 21
Views: 1,260
Posted By 1BDWAGN
Post All good suggestions so far. SBJeep, I actually...

All good suggestions so far.
SBJeep, I actually took the vacuum hose for the power valve disconnected it at the manifold and sucked on it. I thought I would have sucked in some gas if it was...
Forum: General FSJ Tech 03-15-2005, 10:20 AM
Replies: 21
Views: 1,260
Posted By 1BDWAGN
Post I thought for sure on my re-test I would pass....

I thought for sure on my re-test I would pass. Nope still to high on CO. Here are the initial test results
My vehicle Standard
HC 2.59 3.00
CO 45.86 25.00
NOX 5.41 5.50
2nd...
Showing results 1 to 25 of 184

 
Forum Jump

All times are GMT -6. The time now is 08:58 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
corner corner