International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums
Reload this Page Search Results

Page 1 of 17 1 2311 > Last »
Showing results 1 to 25 of 401
Search took 0.02 seconds. Search: Posts Made By: yossarian19
Forum: General FSJ Tech 11-27-2019, 10:05 AM
Replies: 18
Views: 383
Posted By yossarian19
I used a Motorola replacement 10SI meant for...

I used a Motorola replacement 10SI meant for marine use from Ebay.
The bottom flange, I had to grind down a bit and drill & tap a new hole for the "slider" bolt.
Easy enough to do and it's a lot...
Forum: General FSJ Tech 11-23-2019, 10:04 AM
Replies: 62
Views: 2,648
Posted By yossarian19
I haven't driven mine in the SJ much at all yet....

I haven't driven mine in the SJ much at all yet. In XJ vehicles with the 4.0, I've got a *ton* of miles driving them.
First gear is a bit deeper than the TH400, second is darn similar and third is...
Forum: General FSJ Tech 11-18-2019, 09:29 PM
Replies: 9
Views: 291
Posted By yossarian19
Also - power is not so limited as you might think...

Also - power is not so limited as you might think with an I6.
You can use the 4.2 liter's crank & rods (if savable) and a 4.0 block, you get 4.5 liters stock bore or 4.6 / 4.7 with a 0.030 or...
Forum: General FSJ Tech 11-16-2019, 05:29 PM
Replies: 31
Views: 1,755
Posted By yossarian19
Is there a thread problem, or is it just me? I...

Is there a thread problem, or is it just me? I don't see any photos
Forum: General FSJ Tech 11-01-2019, 09:22 AM
Replies: 62
Views: 2,648
Posted By yossarian19
Overkill. Plumb it through the radiator, for...

Overkill.

Plumb it through the radiator, for sure, and add a small cooler (think OEM sizing for a similar rig)
It's easy to go overboard here. What you want to remember is that a transmission has...
Forum: Street & Performance 10-13-2019, 04:43 PM
Replies: 51
Views: 7,076
Posted By yossarian19
Any update?

Any update?
Forum: General FSJ Discussion 09-30-2019, 09:19 PM
Replies: 6
Views: 270
Posted By yossarian19
The LS swap is far and away the most common. I...

The LS swap is far and away the most common. I haven't done one in an FSJ but it really wasn't hard to get it working in my other truck.
The LS platform has all of the parts support you could ever...
Forum: General FSJ Tech 09-07-2019, 09:47 PM
Replies: 62
Views: 2,648
Posted By yossarian19
Pretty sure what you need is a Dana 300 clocking...

Pretty sure what you need is a Dana 300 clocking ring if you have passenger's drop,
flip ring if you have driver's.
I've got a flip ring I'd let go for cheap + shipping (I needed the clocking ring....
Forum: General FSJ Tech 06-07-2019, 09:08 PM
Replies: 3
Views: 698
Posted By yossarian19
I like it. I may wind up sacrificing my spare...

I like it.
I may wind up sacrificing my spare tire to do something like this. Right now I have TBI & a TBI pump in the stock tank, but I picked up an MPFI manifold so... this might be happening...
Forum: General FSJ Tech 04-19-2019, 06:01 PM
Replies: 3
Views: 217
Posted By yossarian19
Also, you are 100% correct about varied valve...

Also, you are 100% correct about varied valve states & tight / loose rockers. The tight ones, of course, are the ones with valve spring tension on them.
I think the 'most correct' thing is to roll...
Forum: General FSJ Tech 04-15-2019, 08:51 PM
Replies: 9
Views: 534
Posted By yossarian19
IIRC The Dana 44 is good for 3,500 lbs gross axle...

IIRC The Dana 44 is good for 3,500 lbs gross axle weight. That's vehicle, payload and tongue weight. The axle may not be the limiting factor. There should be a placard, I think on your driver's door,...
Forum: General FSJ Tech 11-23-2018, 05:43 PM
Replies: 14
Views: 902
Posted By yossarian19
What you've got there is a new hole drilled off...

What you've got there is a new hole drilled off to one side to account for the lateral displacement caused by the lift.
Go back to the original hole and add a weld washer if you are concerned or if...
Forum: General FSJ Tech 11-12-2018, 11:29 PM
Replies: 44
Views: 7,871
Posted By yossarian19
Y'know, that was my first thought. I looked at it...

Y'know, that was my first thought. I looked at it real close though and I couldn't see that the input shaft had a removable retainer. It looks like it was cast as once piece with the back half of the...
Forum: General FSJ Tech 11-12-2018, 12:09 PM
Replies: 44
Views: 7,871
Posted By yossarian19
I found my problem. Threads I'd read were...

I found my problem.
Threads I'd read were talking about driver's drop transfer cases. I ASSumed that because the Dodge case was 23 spline & NP 6-bolt attachment it would go right in.
Turns out, the...
Forum: General FSJ Tech 11-12-2018, 09:47 AM
Replies: 11
Views: 641
Posted By yossarian19
Change axle gears, change tire size, or put in an...

Change axle gears, change tire size, or put in an overdrive transmission.
Guess you could drive slower.
That's about it.
Forum: General FSJ Tech 11-11-2018, 03:01 PM
Replies: 44
Views: 7,871
Posted By yossarian19
Welp, I posted above that a 208D and AW4 bolt up...

Welp, I posted above that a 208D and AW4 bolt up with a 7/8" spacer.
I'd read that, somewhere, or maybe a couple places.
I don't know what the deal is yet but those are the parts I'm trying to use...
Forum: General FSJ Tech 11-11-2018, 09:40 AM
Replies: 7
Views: 538
Posted By yossarian19
"Fix what you have" is usually your...

"Fix what you have" is usually your best bet.
Alternately, talk to your local smog referee and see what carbs they would be OK with. Who knows? They might even talk about some of the bolt on EFI...
Forum: General FSJ Tech 11-10-2018, 11:32 AM
Replies: 31
Views: 2,841
Posted By yossarian19
I know it's a thread resurrection but I'm doing...

I know it's a thread resurrection but I'm doing the same thing as the OP (NP208-D behind an AW4) and using a 7/8" spacer.
Still having a hell of a time getting the 208 seated to the AW4 - I've been...
Forum: General FSJ Tech 10-24-2018, 04:42 PM
Replies: 5
Views: 794
Posted By yossarian19
Whew! Thanks for the info on that spacer ring -...

Whew! Thanks for the info on that spacer ring - that'll save me all manner of grief. I was about to get the trans onto the jack & try to stab it. Glad I saw this first!
Forum: General FSJ Tech 10-24-2018, 06:49 AM
Replies: 5
Views: 794
Posted By yossarian19
Yep, sure enough. It's not a symmetrical patten,...

Yep, sure enough.
It's not a symmetrical patten, the AW4 plate does indeed go on but only one way.
The machinist kinda dismissed me when I said I didn't think it was symmetrical. Oh well. I've...
Forum: General FSJ Tech 10-23-2018, 06:43 AM
Replies: 10
Views: 790
Posted By yossarian19
There's more involved. The way the leaf springs...

There's more involved.
The way the leaf springs attach to the frame is different as is their mounting width on the axles.
It could be done with new leaf spring perches and a welder. You'd need to...
Forum: General FSJ Tech 10-21-2018, 10:31 AM
Replies: 44
Views: 7,871
Posted By yossarian19
Yep. AW4 + 208 "D" works but you need a...

Yep. AW4 + 208 "D" works but you need a 7/8 or 1" spacer between the tcase and trans. Use a Dana 300 clocking / flip ring but make sure you get the thick one ( think some are listed at 3/8 thick) or...
Forum: General FSJ Tech 10-20-2018, 01:57 PM
Replies: 5
Views: 794
Posted By yossarian19
Couple AW4 swap questions

My Google-Fu hasn't turned up the answers yet, so here I go..
1. I've got a '75 401 / TH400 flex plate. It sure looks to be a different bolt pattern at the crank than the 1995 4.0 flex plate I picked...
Forum: General FSJ Tech 10-07-2018, 09:19 AM
Replies: 59
Views: 2,767
Posted By yossarian19
IIRC on an open knuckle Dana 44 (ball joints...

IIRC on an open knuckle Dana 44 (ball joints instead of the big round knuckle on the end of the axle tube) there is nothing keeping crud from entering the tube. The inner seal is all that prevents...
Forum: General FSJ Tech 10-05-2018, 10:21 PM
Replies: 8
Views: 858
Posted By yossarian19
You want to look around the shop, see who's...

You want to look around the shop, see who's working on what, and talk to other people with vehicles like yours and see who they go to and how they like the service.
Don't be worried about a mess in...
Showing results 1 to 25 of 401
Page 1 of 17 1 2311 > Last »

 
Forum Jump

All times are GMT -6. The time now is 08:23 AM.

Contact Us - International Full Size Jeep Association - Archive - Top

Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner IFSJA.org hosting provided by Golden Computer Service.
© 2000-2006 IFSJA Site Staff.   Jeep® is a registerd trademark of DaimlerChrysler. 		corner